-- *****************************************************************
-- CISCO-MEMORY-POOL-MIB
--
-- February 1996, Jeffrey T. Johnson
--
-- July 2001, Seth Wang
--
-- Copyright (c) 2001 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************CISCO-MEMORY-POOL-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Integer32,Gauge32FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
DisplayString,TruthValueFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
ciscoMgmt
FROM CISCO-SMI
Percent
FROM CISCO-QOS-PIB-MIB;ciscoMemoryPoolMIB MODULE-IDENTITYLAST-UPDATED"200107310000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Postal: Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: +1 408 526 4000
E-mail: cs-snmp@cisco.com"DESCRIPTION"MIB module for monitoring memory pools"REVISION"200107310000Z"DESCRIPTION"Added a new table, ciscoMemoryPoolUtilizationTable, which
provides information about memory utilization."REVISION"199602010000Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoMgmt 48}CiscoMemoryPoolTypes ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Represents the different types of memory pools that
may be present in a managed device. Memory pools can
be roughly categorized into two groups, predefined
pools and dynamic pools. The following pool types
are currently predefined:
1: processor memory
2: i/o memory
3: pci memory
4: fast memory
5: multibus memory
Dynamic pools will have a pool type value greater than
any of the predefined types listed above.
Note that only the processor pool is required to be
supported by all devices. Support for other pool types
is dependent on the device being managed."
SYNTAXInteger32(1..65535)ciscoMemoryPoolObjects
OBJECTIDENTIFIER::={ ciscoMemoryPoolMIB 1}ciscoMemoryPoolTable OBJECT-TYPESYNTAXSEQUENCEOF CiscoMemoryPoolEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of memory pool monitoring entries."::={ ciscoMemoryPoolObjects 1}ciscoMemoryPoolEntry OBJECT-TYPESYNTAX CiscoMemoryPoolEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"An entry in the memory pool monitoring table."INDEX{ ciscoMemoryPoolType }::={ ciscoMemoryPoolTable 1}
CiscoMemoryPoolEntry ::=SEQUENCE{
ciscoMemoryPoolType CiscoMemoryPoolTypes,
ciscoMemoryPoolName DisplayString,
ciscoMemoryPoolAlternate Integer32,
ciscoMemoryPoolValid TruthValue,
ciscoMemoryPoolUsed Gauge32,
ciscoMemoryPoolFree Gauge32,
ciscoMemoryPoolLargestFree Gauge32}ciscoMemoryPoolType OBJECT-TYPESYNTAX CiscoMemoryPoolTypes
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The type of memory pool for which this entry
contains information."::={ ciscoMemoryPoolEntry 1}ciscoMemoryPoolName OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A textual name assigned to the memory pool. This
object is suitable for output to a human operator,
and may also be used to distinguish among the various
pool types, especially among dynamic pools."::={ ciscoMemoryPoolEntry 2}ciscoMemoryPoolAlternate OBJECT-TYPESYNTAXInteger32(0..65535)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether or not this memory pool has an
alternate pool configured. Alternate pools are
used for fallback when the current pool runs out
of memory.
If an instance of this object has a value of zero,
then this pool does not have an alternate. Otherwise
the value of this object is the same as the value of
ciscoMemoryPoolType of the alternate pool."::={ ciscoMemoryPoolEntry 3}ciscoMemoryPoolValid OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether or not the remaining objects in
this entry contain accurate data. If an instance
of this object has the value false (which in and of
itself indicates an internal error condition), the
values of the remaining objects in the conceptual row
may contain inaccurate information (specifically, the
reported values may be less than the actual values)."::={ ciscoMemoryPoolEntry 4}ciscoMemoryPoolUsed OBJECT-TYPESYNTAXGauge32UNITS"bytes"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the number of bytes from the memory pool
that are currently in use by applications on the
managed device."::={ ciscoMemoryPoolEntry 5}ciscoMemoryPoolFree OBJECT-TYPE
SYNTAXGauge32UNITS"bytes"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the number of bytes from the memory pool
that are currently unused on the managed device.
Note that the sum of ciscoMemoryPoolUsed and
ciscoMemoryPoolFree is the total amount of memory
in the pool"::={ ciscoMemoryPoolEntry 6}ciscoMemoryPoolLargestFree OBJECT-TYPESYNTAXGauge32UNITS"bytes"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the largest number of contiguous bytes
from the memory pool that are currently unused on
the managed device."::={ ciscoMemoryPoolEntry 7}ciscoMemoryPoolUtilizationTable OBJECT-TYPESYNTAXSEQUENCEOF CiscoMemoryPoolUtilizationEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of memory pool utilization entries. Each of the
objects provides a general idea of how much of the memory
pool has been used over a given period of time. It is
determined as a weighted decaying average."::={ ciscoMemoryPoolObjects 2}ciscoMemoryPoolUtilizationEntry OBJECT-TYPESYNTAX CiscoMemoryPoolUtilizationEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"An entry in the memory pool utilization table."AUGMENTS{ ciscoMemoryPoolEntry }::={ ciscoMemoryPoolUtilizationTable 1}
CiscoMemoryPoolUtilizationEntry ::=SEQUENCE{
ciscoMemoryPoolUtilization1Min Percent,
ciscoMemoryPoolUtilization5Min Percent,
ciscoMemoryPoolUtilization10Min Percent
}ciscoMemoryPoolUtilization1Min OBJECT-TYPESYNTAX Percent
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This is the memory pool utilization for 1 minute."::={ ciscoMemoryPoolUtilizationEntry 1}ciscoMemoryPoolUtilization5Min OBJECT-TYPE
SYNTAX Percent
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This is the memory pool utilization for 5 minutes."::={ ciscoMemoryPoolUtilizationEntry 2}ciscoMemoryPoolUtilization10Min OBJECT-TYPESYNTAX Percent
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This is the memory pool utilization for 10 minutes."::={ ciscoMemoryPoolUtilizationEntry 3}-- notificationsciscoMemoryPoolNotifications
OBJECTIDENTIFIER::={ ciscoMemoryPoolMIB 2}
-- (no notifications are currently defined)-- conformance informationciscoMemoryPoolConformance
OBJECTIDENTIFIER::={ ciscoMemoryPoolMIB 3}ciscoMemoryPoolCompliances
OBJECTIDENTIFIER::={ ciscoMemoryPoolConformance 1}ciscoMemoryPoolGroups
OBJECTIDENTIFIER::={ ciscoMemoryPoolConformance 2}-- compliance statementsciscoMemoryPoolCompliance MODULE-COMPLIANCESTATUSdeprecated-- superceded by ciscoMemoryPoolComplianceRev1DESCRIPTION"The compliance statement for entities which implement
the Cisco Memory Pool MIB"
MODULE-- this moduleMANDATORY-GROUPS{ ciscoMemoryPoolGroup }::={ ciscoMemoryPoolCompliances 1}ciscoMemoryPoolComplianceRev1 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for entities which implement
the Cisco Memory Pool MIB"MODULE-- this moduleMANDATORY-GROUPS{ ciscoMemoryPoolGroup }GROUP ciscoMemoryPoolUtilizationGroup
DESCRIPTION"Per memory pool utilization statistics is mandatory for
the managed system that supports memory pool utilization."::={ ciscoMemoryPoolCompliances 2}
-- units of conformanceciscoMemoryPoolGroup OBJECT-GROUPOBJECTS{
ciscoMemoryPoolName,
ciscoMemoryPoolAlternate,
ciscoMemoryPoolValid,
ciscoMemoryPoolUsed,
ciscoMemoryPoolFree,
ciscoMemoryPoolLargestFree
}STATUScurrentDESCRIPTION"A collection of objects providing memory pool monitoring."::={ ciscoMemoryPoolGroups 1}ciscoMemoryPoolUtilizationGroup OBJECT-GROUPOBJECTS{
ciscoMemoryPoolUtilization1Min,
ciscoMemoryPoolUtilization5Min,
ciscoMemoryPoolUtilization10Min
}STATUScurrent
DESCRIPTION"An optional group providing a collection of memory pool
utilization objects."::={ ciscoMemoryPoolGroups 2}END